2/3 drop kit??

[nikslightning]

Im looking for a 2/3 drop kit for the L. Any suggestions?? Also, if anyone has a pic. of a 2/3 drop on there L, can I take a peek?

Thanks
Nick

 

[djy]

Here is a picture of my Black 2000 Lightning with the Bell Tech 3/4 and Western Chassis 2 inch A-arms. This drop is a 4/4.

djy

Swanson Chip
JL #3 pulley
JL Drive Shaft Loop
Air Raid With 10 inch S&B Big Mouth Filter
Bell Tech 3/4 Drop, C-Section Rear Frame
Western Chassis 2 inch A-arms
Doetsch Tech Nitro-Slammer rear Shocks, Front shocks Edelbrock
Tinted Windows 5% Smoke Tint
Windshield 50% tint
Clear Corners
2001 Head and tail lights
PIAA Super White Headlites
Carbon Fiber Dash Kit
Keyless Door Pad
Trenz Top and Bottom Polished Billet Grills
Trenz Billet Foot Pedals
Trenz Billet Antenna
250A Punch Amp
Sony XplodX Amp XM-604EQX
4 Polk dX7 3-way speakers
MTX-ThunderForm with 2-10 inch subwoofers 6000 series
Calf. Custom 1 piece monogramed plush carpet mat
Ford System 4 Alarm
2001 20 inch Chrome rims
295-40-20 Goodyear HPZR
MagnaFlow Muffler

Born 5/1/2000
#2577

 

[Chris Wood]

Do a search, this topic has been covered MANY times.

 

[nikslightning]

Did the search!.......Helpless. No new information.

Anyone have any info. on a 2/3 drop kit??

Thanks
Nick

 

[KT]

If this picture shows up (they don't seem to work anymore) this is a 2/3 drop.

 

[KT]

Try again.

 

[nikslightning]

Thanks KT, your truck looks great! Where did you get the kit from?

Nick

 

[KT]

I used Bell Tech shackles in the rear & cut 1/2 coil from the stock front springs. Handles much better now.

 

[DR.D]

front spring

How did you cut the front spring. Did you just remove, measure height, and cut?? I like your truck's stance. Just right.Was yours sitting high in the rear when you got it or was it level?

 

[KT]

DR.D

I cut the spring with a 4" disc grinder ( do not use a torch). Only cut 1/2 of a complete coil off. It won't seem like much, but it drops the front about 1", then about 2" after it settles. My truck was about 1" high in the rear when I got it.

 

[iculokn]

Here is a picture of the Bell Tech 3/4 kit. It comes out to a 2/4 on a L and when you move the rear shakel to the 2nd hole it comes out to a 2/3 kit!!

 

[DR.D]

KT

Thanks, sounds easy enough but I may do 3/4 . Yea mine has the 70's air shock look too. 2-inch shackles are a must for mine. I want it 2-3 real inches lower and I would still like to keep a little rake to it. If I have it long enough, I'd like to go full pro street look with tubs.
BTW, that red Gen 1 sure looks good. I had a red 93 before the 01. Still think they look awesome. If they would have put a 350+hp motor in that I would have liked it more. They missed the mark on hp in the Gen 1. Lot of potential but it shouldn't require you to get it to go. It comes from SVT. They should have searched longer for the pulse.

 

[Caka]

Here is a picture of the Bell Tech 3/4 kit. It comes out to a 2/4 on a L and when you move the rear shakel to the 2nd hole it comes out to a 2/3 kit!!

iculokn,
Your truck looks great!! I just have a couple of questions. What is all included in the bell-Tech kit? Why is there an inch difference between an L and a regular f-150 in the front? And are you serious about the rear shackle to the second hole = 1 inch remark? This might be the kit that I will get if it can be made a 2-3. Thanks!!